Tweet
Errors in test 10 and test 13 with new dual channel cards, should I request warranty?
Hello everyone, I'm new here. First of all I've read some of your post and recently tried the software, you're geniuses, great work. Sorry my bad English.
I just hot 2 new cards 1RX8 Hyperx Fury HX426C16FB3/8 2666MHz DDR4 CL16, put them on a HP Higos Motherboard using dual channel (HP recommends PC4-19200 DRR4-2400). Everything works fine, I just mounted them on the mother board since Kingston assures functionality Plug N Play with 2400MHz and 2666MHz AMD systems.
I read about you guys and did a full test with the 2 cards installed. This were the results.
System Information
Result summary
I know you say that any error means something wrong, and that test 13 isn't something I should bother since I use my PC for work and gaming only, I can take the risk.
Test 10 errors worry me a little, honestly I'm a newbie and can't figure out what the results means, I only noticed that it's the same address.
Are those test 10 errors related with my dual channel configuration? Or with the fact that those cards automatically set the max frequency allowed by JEDEC? Should I test my cards individually?
Thank you !
I just hot 2 new cards 1RX8 Hyperx Fury HX426C16FB3/8 2666MHz DDR4 CL16, put them on a HP Higos Motherboard using dual channel (HP recommends PC4-19200 DRR4-2400). Everything works fine, I just mounted them on the mother board since Kingston assures functionality Plug N Play with 2400MHz and 2666MHz AMD systems.
I read about you guys and did a full test with the 2 cards installed. This were the results.
System Information
| CPU Type | AMD Ryzen 5 1400 Quad-Core |
| CPU Clock | 3194 MHz [Turbo: 3194.3 MHz] |
| # Logical Processors | 8 |
| L1 Cache | 8 x 96K (57515 MB/s) |
| L2 Cache | 8 x 512K (51963 MB/s) |
| L3 Cache | 1 x 8192K (26722 MB/s) |
| Memory | 16303M (15475 MB/s) |
| DIMM Slot #0 | 8GB DDR4 XMP PC4-21300 |
| Kingston / KHX2666C16/8G / D7A72491 | |
| 16-18-18-39 / 2666 MHz / 1.200V | |
| DIMM Slot #1 | 8GB DDR4 XMP PC4-21300 |
| Kingston / KHX2666C16/8G / BAA724F5 | |
| 16-18-18-39 / 2666 MHz / 1.200V |
Result summary
| Test Start Time | 2020-07-13 19:00:43 |
| Elapsed Time | 3:37:20 |
| Memory Range Tested | 0x0 - 41F380000 (16883MB) |
| CPU Selection Mode | Parallel (All CPUs) |
| ECC Polling | Enabled |
| # Tests Passed | 45/48 (93%) |
| Lowest Error Address | 0x2C1F29C (44MB) |
| Highest Error Address | 0x2C1F29C (44MB) |
| Bits in Error Mask | 0000000010000000 |
| Bits in Error | 1 |
| Max Contiguous Errors | 1 |
| Test | # Tests Passed | Errors |
| Test 0 [Address test, walking ones, 1 CPU] | 4/4 (100%) | 0 |
| Test 1 [Address test, own address, 1 CPU] | 4/4 (100%) | 0 |
| Test 2 [Address test, own address] | 4/4 (100%) | 0 |
| Test 3 [Moving inversions, ones & zeroes] | 4/4 (100%) | 0 |
| Test 4 [Moving inversions, 8-bit pattern] | 4/4 (100%) | 0 |
| Test 5 [Moving inversions, random pattern] | 4/4 (100%) | 0 |
| Test 6 [Block move, 64-byte blocks] | 4/4 (100%) | 0 |
| Test 7 [Moving inversions, 32-bit pattern] | 4/4 (100%) | 0 |
| Test 8 [Random number sequence] | 4/4 (100%) | 0 |
| Test 9 [Modulo 20, ones & zeros] | 4/4 (100%) | 0 |
| Test 10 [Bit fade test, 2 patterns, 1 CPU] | 2/4 (50%) | 2 |
| Test 13 [Hammer test] | 3/4 (75%) | 2 |
| Last 10 Errors |
| 2020-07-13 22:18:10 - [Data Error] Test: 10, CPU: 0, Address: 2C1F29C, Expected: FFFFFFFF, Actual: EFFFFFFF |
| 2020-07-13 21:20:01 - [Data Error] Test: 13, CPU: 0, Address: 2C1F29C, Expected: 9EB28E23, Actual: 8EB28E23 |
| 2020-07-13 21:18:37 - [Data Error] Test: 10, CPU: 0, Address: 2C1F29C, Expected: FFFFFFFF, Actual: EFFFFFFF |
I know you say that any error means something wrong, and that test 13 isn't something I should bother since I use my PC for work and gaming only, I can take the risk.
Test 10 errors worry me a little, honestly I'm a newbie and can't figure out what the results means, I only noticed that it's the same address.
Are those test 10 errors related with my dual channel configuration? Or with the fact that those cards automatically set the max frequency allowed by JEDEC? Should I test my cards individually?
Thank you !
Comment