Passmark DiskCheckup, explaining results help

[rowfar]

Hey Again made a new thread cuz of the large amount of text needed to be copied. I ran a new Disk test using your software Passmark DiskCheckup and I would like some help explaining the results of the test to me, I am not that good with hardware issues. I don't need everything explained, but I would like to know whether my computer issues (BSOD, ScreenFreeze's when playing MW2) could be caused by my harddisk. Atleast the hardware is good enough so it's harddisk or memory. Can't be software since I just did a new install of Windows 7 x64.

[IMG]file:///C:/Users/Lintsen/AppData/Local/Temp/moz-screenshot.png[/IMG]Results:

*** DiskCheckup V3.0 Build: 1000 Report ***

SmartDisk DLL Version: SysInfo v1.0 Build: 1001
Time of export: 14:58:10 13-jul-2010

Device information:
Device ID: 0
Interface: ATA
Device Capacity: 238473 MB
Serial Number: S09QJ1ML606997
Model Number: SAMSUNG SP2504C
Firmware Revision: VT100-41
Partitions:
C: 131067 MB
D: 107406 MB

ATA information:

Disk geometry:
Cylinders: 98308
Tracks/Cylinder: 138
Sectors/Track: 36
Bytes/Sector: 512
Total disk sectors: 488397168
Logical sector size: 512
Physical sector size: 512
Media rotation rate: N/A
Buffer size: 8192 KB
ECC size: 4 Bytes

Standards compliance:
ATA8-ACS Supported: No
ATA/ATAPI-7 Supported: Yes
ATA/ATAPI-6 Supported: Yes
ATA/ATAPI-5 Supported: Yes
ATA/ATAPI-4 Supported: Yes
World Wide ID: 50000F001B606997

Feature support:
SMART supported: Yes
SMART enabled: Yes
SMART self-test supported: Yes
SMART error log supported: Yes
LBA supported: Yes
IORDY supported: Yes
CFast supported: No
DMA supported: Yes
Maximum Multiword DMA mode supported: 2
Multiword DMA selected: None
Maximum UltraDMA mode supported: 6
UltraDMA selected: 5
Maximum PIO mode supported: 4
SATA Compliance: Yes
NCQ priority information supported: No
Unload while NCQ commands are outstanding supported: No
Phy Event Counters supported: Yes
Receipt of power management requests supported: Yes
NCQ feature set supported: Yes
SATA Gen2 Signaling Speed (3.0Gb/s) supported: Yes
SATA Gen1 Signaling Speed (1.5Gb/s) supported: Yes
Software Settings Preservation: Supported, Enabled
In-order data delivery: Not supported
Initiating power management: Supported, Disabled
DMA Setup auto-activation: Supported, Disabled
Non-zero buffer offsets: Not supported
Trusted Computing supported: No
Host Protected Area (HPA) supported: Yes
Read look-ahead supported: Yes
Read look-ahead enabled: Yes
Write cache supported: Yes
Write cache enabled: Yes
Power management supported: Yes
Security mode supported: Yes
Security mode enabled: No
Device Configuration Overlay (DCO) supported: Yes
48bit Addressing supported: Yes
Auto Acoustic Managment (AAM) supported: Yes
Auto Acoustic Managment (AAM) enabled: No
Power-up in Standby (PUIS) supported: No
Advanced Power Management (APM) supported: No
CompactFlash Association (CFA) supported: No
General Purpose Logging (GPL) supported: Yes
Streaming supported: No
Media card pass through supported: No
Extended power conditions supported: No
Extended status reporting supported: No
Write-read-verify supported: No
Free-fall control supported: No
TRIM command supported: No
SCT command transport supported: Yes
NV Cache enabled: No


SMART ATTRIBUTES:
ID Description Raw Value Status Value Worst
-----------------------------------------------------------------------------------------------------
1 Raw Read Error Rate 0x000000000000 OK 100 100
3 Spin Up Time 0x0000000017C0 OK 100 100
4 Start/Stop Count 0x000000001764 OK 95 95
5 Reallocated Sector Count 0x000000000000 OK 253 253
7 Seek Error Rate 0x000000000000 OK 253 253
8 Seek Time Performance 0x000000000000 OK 253 253
9 Power On Time 0x000000002A8A OK 100 100
10 Spin Retry Count 0x000000000000 OK 253 253
11 Calibration Retry Count 0x000000000000 OK 253 253
12 Power Cycle Count 0x000000000C64 OK 97 97
187 Reported Uncorrectable Errors 0x000000321549 OK 1 1
190 Temperature Difference from 100 0x00000000001F OK 145 115
194 Temperature 31 C OK 145 115
195 Hardware ECC Recovered 0x0000003649EC OK 100 100
196 Reallocation Event Count 0x000000000000 OK 253 253
197 Current Pending Sector Count 0x000000000000 OK 253 100
198 Uncorrectable Sector Count 0x000000000000 OK 253 253
199 UltraDMA CRC Error Count 0x000000000000 OK 200 200
200 Write Error Count 0x000000000000 OK 100 100
201 Off Track Errors 0x000000000000 OK 253 100
202 Data Address Mark Errors 0x000000000000 OK 253 253

Tried my best to make them fix up but kinda messy

[rowfar]

S.M.A.R.T non messed up.

SMART ATTRIBUTES:
ID Description Raw Value Status Value Worst
-----------------------------------------------------------------------------------------------------
1 Raw Read Error Rate 0x000000000000 OK 100 100
3 Spin Up Time 0x0000000017C0 OK 100 100
4 Start/Stop Count 0x000000001764 OK 95 95
5 Reallocated Sector Count 0x000000000000 OK 253 253
7 Seek Error Rate 0x000000000000 OK 253 253
8 Seek Time Performance 0x000000000000 OK 253 253
9 Power On Time 0x000000002A8A OK 100 100
10 Spin Retry Count 0x000000000000 OK 253 253
11 Calibration Retry Count 0x000000000000 OK 253 253
12 Power Cycle Count 0x000000000C64 OK 97 97
187 Reported Uncorrectable Errors 0x000000321549 OK 1 1
190 Temperature Difference from 100 0x00000000001F OK 145 115
194 Temperature 31 C OK 145 115
195 Hardware ECC Recovered 0x0000003649EC OK 100 100
196 Reallocation Event Count 0x000000000000 OK 253 253
197 Current Pending Sector Count 0x000000000000 OK 253 100
198 Uncorrectable Sector Count 0x000000000000 OK 253 253
199 UltraDMA CRC Error Count 0x000000000000 OK 200 200
200 Write Error Count 0x000000000000 OK 100 100
201 Off Track Errors 0x000000000000 OK 253 100
202 Data Address Mark Errors 0x000000000000 OK 253 253

[David (PassMark)]

The disk is reporting that all its attributes are OK. So it should make you less suspect of a low level disk issue.

If you are getting a BSOD then you should collect the details from the blue screen (or several of them if you see them often). There are often interesting details on the blue screen.